查人人中国名人网饥荒青蛙雨时间:英译汉 急 希望大家能帮帮忙！谢谢！（6）
来源：百度文库 编辑：查人人中国名人网 时间：2024/05/03 01:39:35
Troubleshooting problems
The message file is an iteration by iteration account of the simulation. It shows how close each iteration is to converging to the final solution by calculating a relative error norm between successive steps for both nodal velocities and nodal forces. There is also information given on node contact being generated and also if there is a sudden stop. The log file is an account of the module execution
Message file messages
If a simulation stops early, it is recommended to check the end of the message file to see why the simulation stopped. While a simulation is run under the batch mode of operation, there are three places in which the end of operation may be indicated. The message file is where the simulation will indicate a normal stoppage of the FEM module. If there is an abnormal stoppage in simulation, due to an illegal operation in the FEM module or in the mesh generation, this will be indicated in either the .LOG file or in the command window where DEFORM was intially called. This may be also accompanied by a core file which should be deleted as soon as possible since they often consume a large amount of disk space.
Simulation aborted by user
When DEFORM is installed, the permission for the status file (which monitors simulations running on the machine) should be set using the command 'chmod 777 DEFORM.STA'. If this is not done, the FEM engine cannot write to the status file and hence exits. To restart the simulation, first go to the DEFORM_DIR, run INSTALL2D and select the option to regenerate the status file.
Note: If the user gets the message Command not found, the user should run the INSTALL2D by typing ./INSTALL2D. This will force the operating system to override the paths and force the system to run only the file in the current directory.
The message file is an iteration by iteration account of the simulation. It shows how close each iteration is to converging to the final solution by calculating a relative error norm between successive steps for both nodal velocities and nodal forces. There is also information given on node contact being generated and also if there is a sudden stop. The log file is an account of the module execution
Message file messages
If a simulation stops early, it is recommended to check the end of the message file to see why the simulation stopped. While a simulation is run under the batch mode of operation, there are three places in which the end of operation may be indicated. The message file is where the simulation will indicate a normal stoppage of the FEM module. If there is an abnormal stoppage in simulation, due to an illegal operation in the FEM module or in the mesh generation, this will be indicated in either the .LOG file or in the command window where DEFORM was intially called. This may be also accompanied by a core file which should be deleted as soon as possible since they often consume a large amount of disk space.
Simulation aborted by user
When DEFORM is installed, the permission for the status file (which monitors simulations running on the machine) should be set using the command 'chmod 777 DEFORM.STA'. If this is not done, the FEM engine cannot write to the status file and hence exits. To restart the simulation, first go to the DEFORM_DIR, run INSTALL2D and select the option to regenerate the status file.
Note: If the user gets the message Command not found, the user should run the INSTALL2D by typing ./INSTALL2D. This will force the operating system to override the paths and force the system to run only the file in the current directory.
分数太低了。多点可以考虑。
啊,这个也太多了吧?
故障修理问题
信息文件是模拟的重复帐户的一个重复。 资讯科技表示如何结束每个重复是到藉由为节的速度和节的军队计算在连续的步骤之间的一个比较的错误基准对最后解决聚合。 也有被给在节上连络被产生的数据以及如果有一个突然的停止。 圆木文件是组件实行的一个帐户
信息申请信息
如果一个模拟停止得早,它被推荐检查信息文件的结束见到模拟为什么停止。 一个模拟被操作的一届模态支配, 有三个地方在哪一操作的结束可能被指出。 信息文件是模拟将会指出 FEM 组件的一个正常中止的地方。 如果有模拟的一个不正常的中止, 在 FEM 组件中或在网孔世代中由于违法的操作，这将会在任一被指出那。伐木文件或在指令窗户中哪里使是被叫做的 intially变形。 因为他们时常消费很多的磁盘片空间，这也可能随同一个应该尽快地划除的核心文件。
被使用者失败的模拟
当使被安装变形,许可对于状态文件 ( 哪一监视器在机器上的模拟跑) 应该被设定使用指令 'chmod 777 DEFORM.STA' 。 如果这不被做,FEM 引擎对状态不能够写文件而且出口由此而来。 为了重新开始模拟,首先去 DEFORM_DIR, 跑 INSTALL2D 而且选择选项再产生状态文件。
注意: 如果使用者收到信息指令不发现,使用者应该藉由打字跑 INSTALL2D 。/INSTALL2D。 这将会强迫操作系统弃绝路径而且强迫系统只跑现在的目录文件